Skip to main content

LUP Student Papers

LUND UNIVERSITY LIBRARIES

RANS-Based Design Optimization of Matrix Cooling Geometries and Parameters

Doggett, Christopher LU (2026) MVKM01 20261
Department of Energy Sciences
Abstract
Matrix cooling is an unexplored, unutilised and lesser understood method of internal cooling
for turbine blades. It has been used in many successful implemented products but is more
complex and therefore harder to fully understand and utilise to its potential. The aim of this
thesis is to further the understanding of the underlying physics of Matrix cooling and what
role the geometric parameters play in its overall performance and efficiency. Using Reynolds-
Averaged Navier–Stokes (RANS) based computational fluid dynamics (CFD). An automated
simulation and post-processing workflow was developed for the evaluation of multiple geometric
variations simultaneously. The numerical model was validated against experimental results, and
a... (More)
Matrix cooling is an unexplored, unutilised and lesser understood method of internal cooling
for turbine blades. It has been used in many successful implemented products but is more
complex and therefore harder to fully understand and utilise to its potential. The aim of this
thesis is to further the understanding of the underlying physics of Matrix cooling and what
role the geometric parameters play in its overall performance and efficiency. Using Reynolds-
Averaged Navier–Stokes (RANS) based computational fluid dynamics (CFD). An automated
simulation and post-processing workflow was developed for the evaluation of multiple geometric
variations simultaneously. The numerical model was validated against experimental results, and
a mesh independence study was conducted to assess the reliability of the simulations. The
primary findings were establishing that the inclination angle significantly influenced thermal
performance, with the highest Heat Transfer Coefficient (HTC), occurring at the highest tested
inclination angle, due to increased wall impingement, vortex formation, and cross-channel
mixing. Increasing Reynolds number consistently enhanced HTC, while increasing bypass width
reduced it, although the thermal penalty was smaller than expected. Matrix cooling performance
is primarily governed by vortical structures, wall impingement, and flow mixing. The developed
automated CFD workflow provides an efficient basis for further design optimisation while
maintaining relevance to industrial manufacturing requirements (Less)
Popular Abstract
Designing better cooling for hotter, more efficient gas
turbines
The hotter the gas turbine runs, the better the performance. But there’s a catch, to hot, and
everything melts. Efficient internal cooling is the key to running the turbine at temperature well
passed the materials melting point. In this thesis, the design of a complex cooling structure was
investigated by varying its geometric parameters. The results found can be used in the future
to further optimise the geometry to achieve the maximum cooling capacity from this complex
geometry.
A gas turbine converts energy from hot, pressurised gas into useful power. To increase efficiency,
engineers aim to operate turbines at very high temperatures. The problem is that turbine
... (More)
Designing better cooling for hotter, more efficient gas
turbines
The hotter the gas turbine runs, the better the performance. But there’s a catch, to hot, and
everything melts. Efficient internal cooling is the key to running the turbine at temperature well
passed the materials melting point. In this thesis, the design of a complex cooling structure was
investigated by varying its geometric parameters. The results found can be used in the future
to further optimise the geometry to achieve the maximum cooling capacity from this complex
geometry.
A gas turbine converts energy from hot, pressurised gas into useful power. To increase efficiency,
engineers aim to operate turbines at very high temperatures. The problem is that turbine
components must withstand these extreme conditions without overheating. One solution is to
route cooler air through small channels inside the components. These channels carry heat away
from the material and allow the turbine to operate at higher temperatures.
One promising approach is matrix cooling, imagine a maze of many tiny channels twisting and
turning inside the overheating component. These channels disrupt the airflow so it has to take
chaotic paths and reach every part of the component. This creates rotating flows and strong
mixing, this allows the air to not only reach the hot walls but also leave them again after retaining
heat from them.
But how should these channels be designed? In this thesis, three important parameters were
investigated: the angle at which the channels intersect, the width of bypass channels around
the matrix, and the strength of the cooling air flow. Using computer simulations, different
combinations of these parameters were tested to determine which ones had the greatest effect on
cooling performance.
The channel angle was shown to be one of the most important factors. Increasing the angle
strengthened the swirling flow and the interaction between the coolant and the walls. The heat
removal increased with the angle and reached its highest level at 50° among the geometries
investigated. Of course the strength of the cool air flow had a clear effect. When the flow was
increased, the swirling structures and wall interactions became stronger, resulting in more heat
removal.
More unexpectedly the result concerning the bypass channels should that increasing their width
did remove less heat, but the effect was much smaller than expected. This finding is useful
because bypass channels are a design choice made for the manufacturability of the component.
The results therefore suggest that manufacturing requirements can be accommodated while still
removing enough heat.

The simulations were performed using computational fluid dynamics and compared with exper-
imental results to insure that the results were captured correctly. An automated simulation

workflow made it possible to systematically evaluate many different designs at once.
Overall, the results show that cooling performance is mainly controlled by the flow structures
created inside the matrix. For designers, this means that the channel angle and coolant flow
conditions should be given particular attention, while bypass channels may provide more flexibility
than previously assumed. The findings can contribute to future designs that better balance
cooling performance with manufacturing, aerodynamic and mechanical requirements. (Less)
Please use this url to cite or link to this publication:
author
Doggett, Christopher LU
supervisor
organization
course
MVKM01 20261
year
type
H2 - Master's Degree (Two Years)
subject
report number
ISRN LUTMDN/TMHP-26/5715-SE
ISSN
0282-1990
language
English
id
9252582
date added to LUP
2026-11-16 09:00:18
date last changed
2026-11-16 09:00:18
@misc{9252582,
  abstract     = {{Matrix cooling is an unexplored, unutilised and lesser understood method of internal cooling
for turbine blades. It has been used in many successful implemented products but is more
complex and therefore harder to fully understand and utilise to its potential. The aim of this
thesis is to further the understanding of the underlying physics of Matrix cooling and what
role the geometric parameters play in its overall performance and efficiency. Using Reynolds-
Averaged Navier–Stokes (RANS) based computational fluid dynamics (CFD). An automated
simulation and post-processing workflow was developed for the evaluation of multiple geometric
variations simultaneously. The numerical model was validated against experimental results, and
a mesh independence study was conducted to assess the reliability of the simulations. The
primary findings were establishing that the inclination angle significantly influenced thermal
performance, with the highest Heat Transfer Coefficient (HTC), occurring at the highest tested
inclination angle, due to increased wall impingement, vortex formation, and cross-channel
mixing. Increasing Reynolds number consistently enhanced HTC, while increasing bypass width
reduced it, although the thermal penalty was smaller than expected. Matrix cooling performance
is primarily governed by vortical structures, wall impingement, and flow mixing. The developed
automated CFD workflow provides an efficient basis for further design optimisation while
maintaining relevance to industrial manufacturing requirements}},
  author       = {{Doggett, Christopher}},
  issn         = {{0282-1990}},
  language     = {{eng}},
  note         = {{Student Paper}},
  title        = {{RANS-Based Design Optimization of Matrix Cooling Geometries and Parameters}},
  year         = {{2026}},
}