Skip to main content

LUP Student Papers

LUND UNIVERSITY LIBRARIES

Conversion of a Diesel Engine to a Hydrogen-Fuelled Argon Power Cycle: Modelling In GT-Power

Fernandes Martins, Eduardo Jorge LU (2026) KEMR30 20261
Department of Chemistry
Abstract
Introduction: The transport sector remains a major contributor to global greenhouse gas emissions, driving demand for engine concepts that eliminate carbon and nitrogen-oxide output while reusing existing manufacturing infrastructure.
Background: The Argon Power Cycle is an engine concept that replaces air with argon as a working fluid and uses hydrogen as fuel and oxygen as the oxidizer. By exploiting argon’s high specific heat ratio, the theoretical efficiency increases significantly. However, optimal operating parameters for transitioning a conventional engine to this cycle are yet to be established.
Aim: The aim of this project is to work numerically on a Scania DC13 diesel engine, reconfigure it into a closed-loop APC system, and... (More)
Introduction: The transport sector remains a major contributor to global greenhouse gas emissions, driving demand for engine concepts that eliminate carbon and nitrogen-oxide output while reusing existing manufacturing infrastructure.
Background: The Argon Power Cycle is an engine concept that replaces air with argon as a working fluid and uses hydrogen as fuel and oxygen as the oxidizer. By exploiting argon’s high specific heat ratio, the theoretical efficiency increases significantly. However, optimal operating parameters for transitioning a conventional engine to this cycle are yet to be established.
Aim: The aim of this project is to work numerically on a Scania DC13 diesel engine, reconfigure it into a closed-loop APC system, and identify the best operating window that maximises efficiency within mechanical limits.
Methods: A 1D engine model was provided in GT-Power and it was validated against experimental motoring-loss and load sweep data for three working fluid mixtures. The validated model was then reconfigured as a closed-loop containing a condenser, phase separator, and hydrogen and oxygen injectors. A design-of-experiments study was conducted by sweeping the compression ratio, boost pressure, and the heat transfer multiplier, using the gross indicated efficiency as the primary response metric.
Results: The simulations revealed that gross indicated efficiency peaks at a compression ratio of 10-11, and declines sharply beyond 15 as in-cylinder heat losses dominate the cycle. A peak gross indicated efficiency of approximately 58% was achieved at a compression ratio of 10 and 3 bar boost, keeping the peak cylinder pressure within the 220 bar limit of a standard diesel block.
Conclusion: Converting a diesel engine to a closed-loop APC is theoretically feasible, but only at a lower compression ratio than conventional diesel operation, where argon’s efficiency advantage can be realised without exceeding structural mechanical limits. (Less)
Popular Abstract
The transportation area is the biggest contributor to the greenhouse gases, and the European Union is on track to replace fossil fuels as soon as possible with cleaner alternatives. The obvious answer would be to just throw them away old engine and switch to fuel cell or fully electric cars. However, that means dumping of a century’s worth of engine tech, all the knowledge we have built around it, and completely rebuilding our current infrastructure. The big question behind my report is: What if we could keep the engine itself and just change what goes insides?
The idea is called Argon Power Cycle. Unlike the traditional engine, it does not have an intake or an exhaust, and it does not use air. Instead, the engine is filled with argon, a... (More)
The transportation area is the biggest contributor to the greenhouse gases, and the European Union is on track to replace fossil fuels as soon as possible with cleaner alternatives. The obvious answer would be to just throw them away old engine and switch to fuel cell or fully electric cars. However, that means dumping of a century’s worth of engine tech, all the knowledge we have built around it, and completely rebuilding our current infrastructure. The big question behind my report is: What if we could keep the engine itself and just change what goes insides?
The idea is called Argon Power Cycle. Unlike the traditional engine, it does not have an intake or an exhaust, and it does not use air. Instead, the engine is filled with argon, a harmless gas that makes up around one percent of the atmosphere, and uses hydrogen as fuel and oxygen to burn it. This leaves you with just water vapour and argon. The steam is cooled down and turned into water, which will be drained away, while argon is captured and redirected again for the next combustion.
Why argon? Because argon behaves differently than air. Since it is made of single atoms, it cannot waste energy by spinning or vibrating. That means the heat from the combustion is used way more effectively. On paper, this makes the engine more efficient.
To test if this actually works, a detail computer model of a real Scania truck engine was built and verified against real-world practical experiments done in the labs at Lund University. Then, the model was tweaked to fit these closed argon cycle conditions, and finally, the new model was run under new operating parameters to find the best settings.
The simulations revealed that the argon engine cannot just copy a normal diesel engine’s setting. If you use the standard compression, the argon inside gets extremely hot, a large part of the energy escapes through the cylinder walls as heat, and the pressure climbs beyond what the engine can safely sustain. The best result came instead at a lower compression ratio, achieving an efficiency of 58%, well above today’s diesel engine, while staying within the pressure limits.
In conclusion, converting an existing diesel engine into a zero-emission argon engine is theoretical possible, it just needs to run more gently than what a conventional engine does. That could offer a faster and cheaper path to cleaning up heavy transportation emissions and the unnecessary rebuilding a new industry from scratch. (Less)
Please use this url to cite or link to this publication:
author
Fernandes Martins, Eduardo Jorge LU
supervisor
organization
alternative title
From Diesel Engine to Argon Power Cycle: Numerical Modelling
course
KEMR30 20261
year
type
H1 - Master's Degree (One Year)
subject
keywords
argon power cycle, engine simulation, GT-Power, internal combustion engine, thermodynamics, physical chemistry
language
English
id
9244222
date added to LUP
2026-06-26 09:12:26
date last changed
2026-06-26 09:12:26
@misc{9244222,
  abstract     = {{Introduction: The transport sector remains a major contributor to global greenhouse gas emissions, driving demand for engine concepts that eliminate carbon and nitrogen-oxide output while reusing existing manufacturing infrastructure.
Background: The Argon Power Cycle is an engine concept that replaces air with argon as a working fluid and uses hydrogen as fuel and oxygen as the oxidizer. By exploiting argon’s high specific heat ratio, the theoretical efficiency increases significantly. However, optimal operating parameters for transitioning a conventional engine to this cycle are yet to be established.
Aim: The aim of this project is to work numerically on a Scania DC13 diesel engine, reconfigure it into a closed-loop APC system, and identify the best operating window that maximises efficiency within mechanical limits.
Methods: A 1D engine model was provided in GT-Power and it was validated against experimental motoring-loss and load sweep data for three working fluid mixtures. The validated model was then reconfigured as a closed-loop containing a condenser, phase separator, and hydrogen and oxygen injectors. A design-of-experiments study was conducted by sweeping the compression ratio, boost pressure, and the heat transfer multiplier, using the gross indicated efficiency as the primary response metric.
Results: The simulations revealed that gross indicated efficiency peaks at a compression ratio of 10-11, and declines sharply beyond 15 as in-cylinder heat losses dominate the cycle. A peak gross indicated efficiency of approximately 58% was achieved at a compression ratio of 10 and 3 bar boost, keeping the peak cylinder pressure within the 220 bar limit of a standard diesel block. 
Conclusion: Converting a diesel engine to a closed-loop APC is theoretically feasible, but only at a lower compression ratio than conventional diesel operation, where argon’s efficiency advantage can be realised without exceeding structural mechanical limits.}},
  author       = {{Fernandes Martins, Eduardo Jorge}},
  language     = {{eng}},
  note         = {{Student Paper}},
  title        = {{Conversion of a Diesel Engine to a Hydrogen-Fuelled Argon Power Cycle: Modelling In GT-Power}},
  year         = {{2026}},
}