Formaldehyde and Hydroxyl Radicals in an HCCI Engine - Calculations and LIF-Measurements
(2007) In SAE technical paper series- Abstract
- Concentrations of hydroxyl radicals and formaldehyde were calculated using homogeneous (HRM) and stochastic reactor models (SRM), and the result was compared to LIF measurements from an optically accessed iso-octane/n-heptane-fuelled homogeneous charge compression ignition (HCCI) engine. The comparison was at first conducted from averaged total concentrations/signal strengths over the entire combustion volume, which showed a good qualitative agreement between experiments and calculations.
Time- and the calculation-inlet-temperature-resolved concentrations of formaldehyde and hydroxyl radicals obtained through HRM are presented. Probability density plots (PDPs) through SRM calculations and LIF measurements are presented... (More) - Concentrations of hydroxyl radicals and formaldehyde were calculated using homogeneous (HRM) and stochastic reactor models (SRM), and the result was compared to LIF measurements from an optically accessed iso-octane/n-heptane-fuelled homogeneous charge compression ignition (HCCI) engine. The comparison was at first conducted from averaged total concentrations/signal strengths over the entire combustion volume, which showed a good qualitative agreement between experiments and calculations.
Time- and the calculation-inlet-temperature-resolved concentrations of formaldehyde and hydroxyl radicals obtained through HRM are presented. Probability density plots (PDPs) through SRM calculations and LIF measurements are presented and compared, showing a very good agreement considering their delicate and sensitive nature. Thus it is concluded that SRM is a valid model for these purposes, justifying the use of SRM in order to extend the evaluated concentration ranges of the analyzed species beyond the detection/separation level.
It is shown that formaldehyde concentration increases slowly, contrary to hydroxyl which is fast developed. Formaldehyde is locally fast consumed once high temperature chemistry has started, and the highest maximum concentrations of formaldehyde are found in cases where low-temperature chemistry was never transitioned to high-temperature ignition. The PDP's from SRM calculations give increased insight of the occurrence and development of autoignition. During the onset of ignition, the regions with the highest formaldehyde concentrations also have the highest concentrations of hydroxyl radicals. The low-temperature heat release (LTHR) maximum occurs before maximum of formaldehyde, and the regions of (for the LTHR regime relatively) high hydroxyl concentrations gradually becomes fewer until they cease to exist; this occurs after the LTHR peak but before formaldehyde maximum. During the transition state all regions have similar formaldehyde concentrations but varying concentrations of hydroxyl. (Less)
Please use this url to cite or link to this publication:
https://lup.lub.lu.se/record/742328
- author
- organization
- publishing date
- 2007
- type
- Contribution to journal
- publication status
- published
- subject
- in
- SAE technical paper series
- publisher
- Society of Automotive Engineers
- external identifiers
-
- scopus:85072419206
- language
- English
- LU publication?
- yes
- additional info
- Document Number: 2007-01-0049
- id
- a6e96b12-2649-4f3e-bc91-f09310f6721d (old id 742328)
- date added to LUP
- 2016-04-04 12:14:27
- date last changed
- 2022-03-23 18:53:03
@article{a6e96b12-2649-4f3e-bc91-f09310f6721d,
abstract = {{Concentrations of hydroxyl radicals and formaldehyde were calculated using homogeneous (HRM) and stochastic reactor models (SRM), and the result was compared to LIF measurements from an optically accessed iso-octane/n-heptane-fuelled homogeneous charge compression ignition (HCCI) engine. The comparison was at first conducted from averaged total concentrations/signal strengths over the entire combustion volume, which showed a good qualitative agreement between experiments and calculations. <br/><br>
<br/><br>
Time- and the calculation-inlet-temperature-resolved concentrations of formaldehyde and hydroxyl radicals obtained through HRM are presented. Probability density plots (PDPs) through SRM calculations and LIF measurements are presented and compared, showing a very good agreement considering their delicate and sensitive nature. Thus it is concluded that SRM is a valid model for these purposes, justifying the use of SRM in order to extend the evaluated concentration ranges of the analyzed species beyond the detection/separation level. <br/><br>
<br/><br>
It is shown that formaldehyde concentration increases slowly, contrary to hydroxyl which is fast developed. Formaldehyde is locally fast consumed once high temperature chemistry has started, and the highest maximum concentrations of formaldehyde are found in cases where low-temperature chemistry was never transitioned to high-temperature ignition. The PDP's from SRM calculations give increased insight of the occurrence and development of autoignition. During the onset of ignition, the regions with the highest formaldehyde concentrations also have the highest concentrations of hydroxyl radicals. The low-temperature heat release (LTHR) maximum occurs before maximum of formaldehyde, and the regions of (for the LTHR regime relatively) high hydroxyl concentrations gradually becomes fewer until they cease to exist; this occurs after the LTHR peak but before formaldehyde maximum. During the transition state all regions have similar formaldehyde concentrations but varying concentrations of hydroxyl.}},
author = {{Tunér, Martin and Amnéus, Per and Mauss, Fabian and Collin, Robert and Nygren, Jenny and Richter, Mattias and Aldén, Marcus and Kraft, Markus and Bhave, Amit N. and Hildingsson, Leif and Johansson, Bengt}},
language = {{eng}},
publisher = {{Society of Automotive Engineers}},
series = {{SAE technical paper series}},
title = {{Formaldehyde and Hydroxyl Radicals in an HCCI Engine - Calculations and LIF-Measurements}},
year = {{2007}},
}