1 – 50 of 59
- show: 50
- |
- sort: year (new to old)
Close
Embed this list
<iframe src=" "
width=" "
height=" "
allowtransparency="true"
frameborder="0">
</iframe>
- 2024
-
Mark
The effect of workpiece grain size on surface integrity in orthogonal cutting of Inconel 718
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Evolution of surface quality in micromilling Ti-6Al-4V alloy with increasing machined length
(
- Chapter in Book/Report/Conference proceeding › Preface to conference proceeding
-
Mark
On the surface integrity of machined aero-engine grade Ni-based superalloy billets produced by the field-assisted sintering technology (FAST) route
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Effect of cooling scheme and coating of drills on hole quality in drilling of Inconel 718
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2023
-
Mark
Recognition of drilling-induced defects in Fiber Reinforced Polymers using Machine Learning
2023) 19th CIRP Conference on Modeling of Machining Operations, CMMO 2023 In Procedia CIRP 117. p.384-389(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Developing a Carbon Accounting Tool for SMEs in the Agri-Food Sector : 30th CIRP Life Cycle Engineering Conference
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Sustainability Assessment of Electronic Waste Remanufacturing: The Case of Laptop
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Eco-social sustainability assessment of manufacturing systems: an LCA-based framework
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2022
-
Mark
Machine Learning based Approach for the Prediction of Surface Integrity in Machining
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Numerical investigations on residual stresses in orthogonal cutting of Ti-6A1-4V
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Numerical and experimental investigation on the residual stresses generated by scanning induction hardening
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2021
-
Mark
FE analysis on the association between tool edge radius and thermal-mechanical load in machining Inconel 718
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Analyzing the Environmental Consequences of Production Processes from a System of Systems Perspective : A Case of Gear Manufacturing in the Automotive Industry
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Simulation of nanometric cutting using molecular dynamics
2021) In Procedia CIRP(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Experimental study and modeling of the heat flux acting on the tool flank when machining
2021) 18th CIRP Conference on Modeling of Machining Operations, CMMO 2021 In Procedia CIRP 102. p.97-102(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Food 4.0 : Implementation of the Augmented Reality Systems in the Food Industry
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2020
-
Mark
Investigation on work hardening phenomenon in turning Inconel 718 with chamfered inserts considering thermal-mechanical loads
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
CBN-based cutting tools with niobium compounds as a binder phase
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2019
-
Mark
Comparing Life Cycle Costing and Performance Part Costing in Assessing Acquisition and Operational Cost of New Manufacturing Technologies
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Comparing acquisition and operation life cycle costs of powder metallurgy and conventional wrought steel gear manufacturing techniques
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Determining process parameters for successful material reclamation of lead-free brass chips using hot forging operations: Lubrication
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Multi-objective testing of different brass alloy components for DFM
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Quantitative analysis of chip segmentation in machining using an automated image processing method
2019) 17th CIRP Conference on Modelling of Machining Operations, CIRP CMMO In Procedia CIRP 82. p.314-319(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2018
-
Mark
Surface Characterization of AD730TM Part Produced in High Speed Turning with CBN tool
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Plastic Deformation and Residual Stress in High Speed Turning of AD730™ Nickel-based Superalloy with PCBN and WC Tools
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Influence of graphite nanoadditives to vegetable-based oil on machining performance when MQCL assisted hard turning
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Tool Wear Mechanisms of pcBN tooling during High-Speed Machining of Gray Cast Iron
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Surface roughness and sub-surface deformation measurements in machining of niobium
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Enhancing Reuse and Resource Recovery of Electrical and Electronic Equipment with Reverse Logistics to Meet Carbon Reduction Targets
2018) 25th CIRP Conference on Life Cycle Engineering, , CIRP LCE 2018 In Procedia CIRP 69. p.980-985(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Consumer Perspectives on longevity and Reliability : A National Study of Purchasing Factors Across Eighteen Product Categories
2018) 25th CIRP Conference on Life Cycle Engineering, , CIRP LCE 2018 In Procedia CIRP 69. p.910-915(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
FE simulation and experimental verification of side-flow and burr formation in machining of oxygen-free copper
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Selecting Cutting Data Tests for Cutting Data Modeling Using the Colding Tool Life Model
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Investigation of the mechanical properties and cutting performance of cBN-based cutting tools with Cr3C2 binder phase.
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
CPR a general Cost Performance Ratio in Manufacturing - A KPI for judgement of different technologies and development scenarios
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2017
-
Mark
International Survey of the Costs of Assessment for Environmental Product Declarations
(
- Contribution to journal › Article
-
Mark
Towards a Sustainable Business Model for Plastic Shopping Bag Management in Sweden
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Computational and Experimental Inverse Problem Approach for Determination of Time Dependency of Heat Flux in Metal Cutting
2017) 16th CIRP Conference on Modelling of Machining Operations (16th CIRP CMMO) In Procedia CIRP 58. p.122-127(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Experimental and Numerical Investigation of Burr Formation in Intermittent Turning of AISI 4140
2017) 16th CIRP Conference on Modelling of Machining Operations (16th CIRP CMMO) In Procedia CIRP 58. p.37-42(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Modeling of Force Build-up Process and Optimization of Tool Geometry when Intermittent Turning
2017) 16th CIRP Conference on Modelling of Machining Operations (16th CIRP CMMO) In Procedia CIRP 58. p.393-398(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
The Influence the Uncut Chip Thickness has on the Stagnation Point in Orthogonal Cutting
2017) 16th CIRP Conference on Modelling of Machining Operations (16th CIRP CMMO) In Procedia CIRP 58. p.13-18(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Sustainability Performance Indicators at Shop Floor Level in Large Manufacturing Companies
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2016
-
Mark
Influence of Cutting Edge Geometry on Force Build-up Process in Intermittent Turning
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Tool Wear and Vibrations Generated When Turning High-chromium White Cast Iron with pCBN Tools
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Numerical Determination of Process Values Influencing the Surface Integrity in Grinding
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
The Adoption of Additive Manufacturing Technology in Sweden
2016) 13th Global Conference on Sustainable Manufacturing - Decoupling Growth from Resource Use 2015 In Procedia CIRP 40. p.7-12(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
- 2015
-
Mark
On the Analytical Representation of Chip Area and Tool Geometry when Oblique Turning with Round Tools. Part 1: Chip Area Parameters under Variation of Side and Back Rake Angle
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Influences of micro mechanical property and microstructure on performance of machining high chromium white cast iron with cBN tools
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Determination of the Thermal Load Distribution in Internal Traverse Grinding using a Geometric-Kinematic Simulation
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
On the Analytical Representation of Chip Area and Tool Geometry when Oblique Turning with Round Tools. Part 2: Variation of Tool Geometry along the Edge Line
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding
-
Mark
Modelling and Experimental Investigation of Cutting Temperature when Rough Turning Hardened Tool Steel with PCBN Tools
(
- Chapter in Book/Report/Conference proceeding › Paper in conference proceeding